ELEKTRONİK ENTEGRE VE PIK (PIC): 220 volt ve bir adet led

26 Eylül 2010 Pazar

220 volt ve bir adet led

220V AC Powered Blinking LED
I needed a pulsating light for a certain signaling. Voltage was 230V. So I decided to make a simple circuit, consisted of a LED diode, two capacitors, two resistors, a diac and a diode. Activity of the circuit is extraordinarily simple. The capacitor charges by the diode and the resistor. When the voltage on the capacitor achieves 30V the diac "releases" the electrical tension and the capacitor empties thorough the diac, LED blinks. Time base is dependent from the capacitor and the resistor, which is in series with diode 1N4007. Capacitor must be at least for 40V.
Ben belirli bir sinyal için bir titreşen ışık gerekiyordu.Voltajı 230V oldu. Bu yüzden basit bir devre için, kararBir LED diyot oluşuyordu
iki kapasitörler, iki dirençler, bir ve bir diyot kardiyak.devre Faaliyet derece basittir.diyot ve direnç ile kondansatör şarj olur.
Zaman kondansatör üzerindeki gerilim kardiyak 30V elde"Bildirileri" elektrik gerilim ve kondansatör tam kardiyak, LED yanıp söner boşaltır.Zaman tabanı kondansatör ve direnç dan bağlıdırhangi diyot 1N4007 seri bulunuyor.Kondansatör 40V en az olmalıdır.

Hiç yorum yok:

Yorum Gönder

LED DİRENÇ HESAPLAMA

All LEDs require current limiting, without a current limiting mechanism the LED will usually burn out in under a second. Adding a simple resistor is the easiest way to limit the current. Use the calculator below to find out the value of resistor you require.

For example if you are wanting to power one of our_blank">red LEDs in an automotive application you would see that the typical forward voltage is 2.0 Volts and the maximum continuous forward current is 30mA. Therefore you would enter 14.5, 2.0 and 30 into the Single LED calculation box. After calculating you get 470ohm 1 watt as the result. Here is a that allows you to enter a resistor value and generate the corresponding color code.

Note: For automotive applications use the actual system voltage, not 12 Volts. Most 12 Volt system actually operate at around 14.5 Volts.

Supply Voltage
VOLTS
Voltage Drop Across LED
VOLTS
Desired LED Current
MILLIAMPS

Calculated Limiting Resistor
OHMS
Nearest higher rated 10% resistor

Calculated Resistor Wattage
WATTS
Safe pick is a resistor with
power rating of (common values are .25W, .5W, and 1W)
WATTS

LEDs in series

LM555 - ASTABLE OSCILLATOR CALCULATOR

LM555 - ASTABLE OSCILLATOR CALCULATOR Resistor values are in Ohms (1K = 1000) - Capacitor values are in Microfarads (1uF = 1)

NOTE: The leakage currents of electrolytic capacitors will affect the actual output results of the timers. To compensate for leakage it is often better to use a higher value capacitor and lower value resistances in the timer circuits.

LM555 Astable Oscillator Circuit Diagram

LM555 - ASTABLE CAPACITOR CALCULATOR

The next calculator can find the capacitance needed for a particular output frequency if the values of R1 and R2 are known.

Value Of R1 Ohms	Value Of R2 Ohms
Frequency Desired Hertz

Capacitance uF

IMPORTANT EXPLANATION

IMPORTANT EXPLANATION

Some published diagrams and explanations of this Blog tested will occur when you try some untested and is not responsible for the problem if the attempt does not want to visit does not attempt to remain on their own request is a responsibility

ÖNEMLİ AÇIKLAMA,

Bu Blogta Yayınlanan şemalar ve açıklamaların bazıları denenmiş bazıları denenmemiş olup denerken meydana gelecek olan problemlerden dolayı sorumluluk kabul edilmez.Siteyi ziyaret eden isterse dener istemezse denemez kendi isteğine kalmış bir sorumluluktur