ELEKTRONİK ENTEGRE VE PIK (PIC): Triac , Thyristor, the electronic AC switch ,Triyak, Thyristor elektronik alternatif akım anahatarı

13 Ocak 2010 Çarşamba

Triac , Thyristor, the electronic AC switch ,Triyak, Thyristor elektronik alternatif akım anahatarı

TRIAC
Triac Şemada gösterim şekli aşağıda ki şekilde gösterilmiştir

DIAC
Diac Şemada gösterim şekli aşağıda ki şekilde gösterilmiştir

DIAC Tristör ün başka bir türüdür. DIAC alternatif akım devrelerinde kullanılır. Tristör de bulunan gate kapısı diac ta bulunmaz.

Thyristor
Tristör katı hal yarı iletken bir cihaz dır. SCR (silikon kontrollü redresörler).

Tristör DC akımı kontrol etmek için kullanılır Bir triyakın aksine bir tek yönde akımı geçirmektedir.
Bir kontrol diyot veya tetiklenen transistöre benzer .

Hiç yorum yok:

Yorum Gönder

LED DİRENÇ HESAPLAMA

All LEDs require current limiting, without a current limiting mechanism the LED will usually burn out in under a second. Adding a simple resistor is the easiest way to limit the current. Use the calculator below to find out the value of resistor you require.

For example if you are wanting to power one of our_blank">red LEDs in an automotive application you would see that the typical forward voltage is 2.0 Volts and the maximum continuous forward current is 30mA. Therefore you would enter 14.5, 2.0 and 30 into the Single LED calculation box. After calculating you get 470ohm 1 watt as the result. Here is a that allows you to enter a resistor value and generate the corresponding color code.

Note: For automotive applications use the actual system voltage, not 12 Volts. Most 12 Volt system actually operate at around 14.5 Volts.

Supply Voltage
VOLTS
Voltage Drop Across LED
VOLTS
Desired LED Current
MILLIAMPS

Calculated Limiting Resistor
OHMS
Nearest higher rated 10% resistor

Calculated Resistor Wattage
WATTS
Safe pick is a resistor with
power rating of (common values are .25W, .5W, and 1W)
WATTS

LEDs in series

LM555 - ASTABLE OSCILLATOR CALCULATOR

LM555 - ASTABLE OSCILLATOR CALCULATOR Resistor values are in Ohms (1K = 1000) - Capacitor values are in Microfarads (1uF = 1)

NOTE: The leakage currents of electrolytic capacitors will affect the actual output results of the timers. To compensate for leakage it is often better to use a higher value capacitor and lower value resistances in the timer circuits.

LM555 Astable Oscillator Circuit Diagram

LM555 - ASTABLE CAPACITOR CALCULATOR

The next calculator can find the capacitance needed for a particular output frequency if the values of R1 and R2 are known.

Value Of R1 Ohms	Value Of R2 Ohms
Frequency Desired Hertz

Capacitance uF

IMPORTANT EXPLANATION

IMPORTANT EXPLANATION

Some published diagrams and explanations of this Blog tested will occur when you try some untested and is not responsible for the problem if the attempt does not want to visit does not attempt to remain on their own request is a responsibility

ÖNEMLİ AÇIKLAMA,

Bu Blogta Yayınlanan şemalar ve açıklamaların bazıları denenmiş bazıları denenmemiş olup denerken meydana gelecek olan problemlerden dolayı sorumluluk kabul edilmez.Siteyi ziyaret eden isterse dener istemezse denemez kendi isteğine kalmış bir sorumluluktur